aboutsummaryrefslogtreecommitdiffstats
path: root/module/zfs/vdev.c
Commit message (Collapse)AuthorAgeFilesLines
...
* Fix dirtying vdev config on with RO spaTom Caputi2018-11-071-2/+3
| | | | | | | | | | This patch simply corrects an issue where vdev_dtl_reassess() could attempt to dirty the vdev config even when the spa was not elligable for writing. Reviewed-by: Matthew Ahrens <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Tom Caputi <[email protected]> Closes #8085
* Make vdev_set_deferred_resilver() recursiveTom Caputi2018-11-071-1/+8
| | | | | | | | | | | | | | | vdev_clear() can call vdev_set_deferred_resilver() with a non-leaf vdev to setup a deferred resilver. However, this function is currently written to only handle leaf vdevs. This bug was introduced with deferred resilvers in 80a91e74. This patch makes this function recursive so that it can find appropriate vdevs to resilver and set vdev_resilver_deferred on them. Reviewed-by: Matthew Ahrens <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Tom Caputi <[email protected]> Issue #7732 Closes #8082
* OpenZFS 9690 - metaslab of vdev with no space maps was flushed during removalSerapheim Dimitropoulos2018-10-191-12/+10
| | | | | | | | | | | | | Authored by: Serapheim Dimitropoulos <[email protected]> Reviewed by: Matt Ahrens <[email protected]> Reviewed by: Brad Lewis <[email protected]> Reviewed by: George Melikov <[email protected]> Approved by: Robert Mustacchi <[email protected]> Ported-by: Brian Behlendorf <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/9690 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4e75ba6826 Closes #8039
* Defer new resilvers until the current one endsTom Caputi2018-10-181-4/+31
| | | | | | | | | | | | | | | | | | | | | | | | | Currently, if a resilver is triggered for any reason while an existing one is running, zfs will immediately restart the existing resilver from the beginning to include the new drive. This causes problems for system administrators when a drive fails while another is already resilvering. In this case, the optimal thing to do to reduce risk of data loss is to wait for the current resilver to end before immediately replacing the second failed drive, which allows the system to operate with two incomplete drives for the minimum amount of time. This patch introduces the resilver_defer feature that essentially does this for the admin without forcing them to wait and monitor the resilver manually. The change requires an on-disk feature since we must mark drives that are part of a deferred resilver in the vdev config to ensure that we do not assume they are done resilvering when an existing resilver completes. Reviewed-by: Matthew Ahrens <[email protected]> Reviewed-by: John Kennedy <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: @mmaybee Signed-off-by: Tom Caputi <[email protected]> Closes #7732
* Improved error handling for extreme rewindsBrian Behlendorf2018-10-121-16/+29
| | | | | | | | | | | | | | | | | | | | | | | The vdev_checkpoint_sm_object(), vdev_obsolete_sm_object(), and vdev_obsolete_counts_are_precise() functions assume that the only way a zap_lookup() can fail is if the requested entry is missing. While this is the most common cause, it's not the only cause. Attemping to access a damaged ZAP will result in other errors. The most likely scenario for accessing a damaged ZAP is during an extreme rewind pool import. Under these conditions the pool is expected to contain damaged objects and the import code was updated to handle this gracefully. Getting an ECKSUM error from these ZAPs after the pool in import a far less likely, therefore the behavior for call paths was not modified. Reviewed-by: Tim Chase <[email protected]> Reviewed-by: Matthew Ahrens <[email protected]> Reviewed-by: Serapheim Dimitropoulos <[email protected]> Signed-off-by: Brian Behlendorf <[email protected]> Closes #7809 Closes #7921
* Revert "Allow ECKSUM in vdev_checkpoint_sm_object()"Brian Behlendorf2018-10-121-8/+4
| | | | | | | | | | This reverts commit e927fc8a522e1c0db89955cc555841aa23bbd634. Reviewed by: Tim Chase <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: Serapheim Dimitropoulos <[email protected]> Signed-off-by: Brian Behlendorf <[email protected]> Closes #7921
* Pool allocation classesDon Brady2018-09-051-28/+183
| | | | | | | | | | | | | | | | | | | | Allocation Classes add the ability to have allocation classes in a pool that are dedicated to serving specific block categories, such as DDT data, metadata, and small file blocks. A pool can opt-in to this feature by adding a 'special' or 'dedup' top-level VDEV. Reviewed by: Pavel Zakharov <[email protected]> Reviewed-by: Richard Laager <[email protected]> Reviewed-by: Alek Pinchuk <[email protected]> Reviewed-by: Håkan Johansson <[email protected]> Reviewed-by: Andreas Dilger <[email protected]> Reviewed-by: DHE <[email protected]> Reviewed-by: Richard Elling <[email protected]> Reviewed-by: Gregor Kopka <[email protected]> Reviewed-by: Kash Pande <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: Matthew Ahrens <[email protected]> Signed-off-by: Don Brady <[email protected]> Closes #5182
* Allow ECKSUM in vdev_checkpoint_sm_object()Brian Behlendorf2018-08-311-4/+8
| | | | | | | | | | | The checkpoint space map object may not be accessible from the vdev's ZAP when it has been damaged. This may be the case when performing an extreme rewind when importing the pool. Reviewed-by: Serapheim Dimitropoulos <[email protected]> Reviewed by: Tim Chase <[email protected]> Signed-off-by: Brian Behlendorf <[email protected]> Closes #7809 Closes #7853
* s/VERIFY/VERIFY3S in vdev_checkpoint_sm_objectTim Chase2018-08-211-1/+2
| | | | | | | | | | Using VERIFY3S allows to view the unexpected error value in the system log. Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: Don Brady <[email protected]> Signed-off-by: Tim Chase <[email protected]> Issue #7809 Closes #7818
* OpenZFS 9112 - Improve allocation performance on high-end systemsPaul Dagnelie2018-07-311-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Overview ======== We parallelize the allocation process by creating the concept of "allocators". There are a certain number of allocators per metaslab group, defined by the value of a tunable at pool open time. Each allocator for a given metaslab group has up to 2 active metaslabs; one "primary", and one "secondary". The primary and secondary weight mean the same thing they did in in the pre-allocator world; primary metaslabs are used for most allocations, secondary metaslabs are used for ditto blocks being allocated in the same metaslab group. There is also the CLAIM weight, which has been separated out from the other weights, but that is less important to understanding the patch. The active metaslabs for each allocator are moved from their normal place in the metaslab tree for the group to the back of the tree. This way, they will not be selected for use by other allocators searching for new metaslabs unless all the passive metaslabs are unsuitable for allocations. If that does happen, the allocators will "steal" from each other to ensure that IOs don't fail until there is truly no space left to perform allocations. In addition, the alloc queue for each metaslab group has been broken into a separate queue for each allocator. We don't want to dramatically increase the number of inflight IOs on low-end systems, because it can significantly increase txg times. On the other hand, we want to ensure that there are enough IOs for each allocator to allow for good coalescing before sending the IOs to the disk. As a result, we take a compromise path; each allocator's alloc queue max depth starts at a certain value for every txg. Every time an IO completes, we increase the max depth. This should hopefully provide a good balance between the two failure modes, while not dramatically increasing complexity. We also parallelize the spa_alloc_tree and spa_alloc_lock, which cause very similar contention when selecting IOs to allocate. This parallelization uses the same allocator scheme as metaslab selection. Performance Results =================== Performance improvements from this change can vary significantly based on the number of CPUs in the system, whether or not the system has a NUMA architecture, the speed of the drives, the values for the various tunables, and the workload being performed. For an fio async sequential write workload on a 24 core NUMA system with 256 GB of RAM and 8 128 GB SSDs, there is a roughly 25% performance improvement. Future Work =========== Analysis of the performance of the system with this patch applied shows that a significant new bottleneck is the vdev disk queues, which also need to be parallelized. Prototyping of this change has occurred, and there was a performance improvement, but more work needs to be done before its stability has been verified and it is ready to be upstreamed. Authored by: Paul Dagnelie <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Serapheim Dimitropoulos <[email protected]> Reviewed by: Alexander Motin <[email protected]> Reviewed by: Brian Behlendorf <[email protected]> Approved by: Gordon Ross <[email protected]> Ported-by: Paul Dagnelie <[email protected]> Signed-off-by: Paul Dagnelie <[email protected]> Porting Notes: * Fix reservation test failures by increasing tolerance. OpenZFS-issue: https://illumos.org/issues/9112 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3f3cc3c3 Closes #7682
* Add support for autoexpand propertyBrian Behlendorf2018-07-231-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While the autoexpand property may seem like a small feature it depends on a significant amount of system infrastructure. Enough of that infrastructure is now in place that with a few modifications for Linux it can be supported. Auto-expand works as follows; when a block device is modified (re-sized, closed after being open r/w, etc) a change uevent is generated for udev. The ZED, which is monitoring udev events, passes the change event along to zfs_deliver_dle() if the disk or partition contains a zfs_member as identified by blkid. From here the device is matched against all imported pool vdevs using the vdev_guid which was read from the label by blkid. If a match is found the ZED reopens the pool vdev. This re-opening is important because it allows the vdev to be briefly closed so the disk partition table can be re-read. Otherwise, it wouldn't be possible to report the maximum possible expansion size. Finally, if the property autoexpand=on a vdev expansion will be attempted. After performing some sanity checks on the disk to verify that it is safe to expand, the primary partition (-part1) will be expanded and the partition table updated. The partition is then re-opened (again) to detect the updated size which allows the new capacity to be used. In order to make all of the above possible the following changes were required: * Updated the zpool_expand_001_pos and zpool_expand_003_pos tests. These tests now create a pool which is layered on a loopback, scsi_debug, and file vdev. This allows for testing of non- partitioned block device (loopback), a partition block device (scsi_debug), and a file which does not receive udev change events. This provided for better test coverage, and by removing the layering on ZFS volumes there issues surrounding layering one pool on another are avoided. * zpool_find_vdev_by_physpath() updated to accept a vdev guid. This allows for matching by guid rather than path which is a more reliable way for the ZED to reference a vdev. * Fixed zfs_zevent_wait() signal handling which could result in the ZED spinning when a signal was not handled. * Removed vdev_disk_rrpart() functionality which can be abandoned in favor of kernel provided blkdev_reread_part() function. * Added a rwlock which is held as a writer while a disk is being reopened. This is important to prevent errors from occurring for any configuration related IOs which bypass the SCL_ZIO lock. The zpool_reopen_007_pos.ksh test case was added to verify IO error are never observed when reopening. This is not expected to impact IO performance. Additional fixes which aren't critical but were discovered and resolved in the course of developing this functionality. * Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for ZFS volumes. This is as good as a unique physical path, while the volumes are not used in the test cases anymore for other reasons this improvement was included. Reviewed by: Richard Elling <[email protected]> Signed-off-by: Sara Hartse <[email protected]> Signed-off-by: Brian Behlendorf <[email protected]> Closes #120 Closes #2437 Closes #5771 Closes #7366 Closes #7582 Closes #7629
* OpenZFS 9426 - metaslab size can exceed offset addressable by spacemapDon Brady2018-07-111-27/+55
| | | | | | | | | | | | Authored by: Don Brady <[email protected]> Reviewed by: Paul Dagnelie <[email protected]> Reviewed by: Matt Ahrens <[email protected]> Ported-by: Brian Behlendorf <[email protected]> Approved by: Dan McDonald <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/9426 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f1c88afb1 Closes #7700
* OpenZFS 9479 - fix wrong format specifier for vdev_idAndriy Gapon2018-07-111-1/+1
| | | | | | | | | | | | | Authored by: Andriy Gapon <[email protected]> Reviewed by: Matt Ahrens <[email protected]> Reviewed by: Giuseppe Di Natale <[email protected]> Reviewed by: George Melikov <[email protected]> Ported-by: Brian Behlendorf <[email protected]> Approved by: Robert Mustacchi <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/9479 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/20aa447c Closes #7699
* OpenZFS 9238 - ZFS Spacemap Encoding V2Serapheim Dimitropoulos2018-07-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Motivation ========== The current space map encoding has the following disadvantages: [1] Assuming 512 sector size each entry can represent at most 16MB for a segment. This makes the encoding very inefficient for large regions of space. [2] As vdev-wide space maps have started to be used by new features (i.e. device removal, zpool checkpoint) we've started imposing limits in the vdevs that can be used with them based on the maximum addressable offset (currently 64PB for a top-level vdev). New encoding ============ The layout can be found at space_map.h and it remains backwards compatible with the old one. The introduced two-word entry format, besides extending the limits imposed by the single-entry layout, also includes a vdev field and some extra padding after its prefix. The extra padding after the prefix should is reserved for future usage (e.g. new prefixes for future encodings or new fields for flags). The new vdev field not only makes the space maps more self-descriptive, but also opens the doors for pool-wide space maps (expected to be used in the log spacemap project). One final important note is that the number of bits used for vdevs is reduced to 24 bits for blkptrs. That was decided as we don't know of any setups that use more than 16M vdevs for the time being and we wanted to fit the vdev field in the space map. In addition that gives us some extra bits in dva_t. Other references: ================= The new encoding is also discussed towards the end of the Log Space Map presentation from 2017's OpenZFS summit. Link: https://www.youtube.com/watch?v=jj2IxRkl5bQ Authored by: Serapheim Dimitropoulos <[email protected]> Reviewed by: Matt Ahrens <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Brian Behlendorf <[email protected]> Approved by: Gordon Ross <[email protected]> Ported-by: Tim Chase <[email protected]> Signed-off-by: Tim Chase <[email protected]> OpenZFS-commit: https://github.com/openzfs/openzfs/commit/90a56e6d OpenZFS-issue: https://www.illumos.org/issues/9238 Closes #7665
* OpenZFS 9166 - zfs storage pool checkpointSerapheim Dimitropoulos2018-06-261-18/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Details about the motivation of this feature and its usage can be found in this blogpost: https://sdimitro.github.io/post/zpool-checkpoint/ A lightning talk of this feature can be found here: https://www.youtube.com/watch?v=fPQA8K40jAM Implementation details can be found in big block comment of spa_checkpoint.c Side-changes that are relevant to this commit but not explained elsewhere: * renames members of "struct metaslab trees to be shorter without losing meaning * space_map_{alloc,truncate}() accept a block size as a parameter. The reason is that in the current state all space maps that we allocate through the DMU use a global tunable (space_map_blksz) which defauls to 4KB. This is ok for metaslab space maps in terms of bandwirdth since they are scattered all over the disk. But for other space maps this default is probably not what we want. Examples are device removal's vdev_obsolete_sm or vdev_chedkpoint_sm from this review. Both of these have a 1:1 relationship with each vdev and could benefit from a bigger block size. Porting notes: * The part of dsl_scan_sync() which handles async destroys has been moved into the new dsl_process_async_destroys() function. * Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write to block device backed pools. * ZTS: * Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg". * Don't use large dd block sizes on /dev/urandom under Linux in checkpoint_capacity. * Adopt Delphix-OS's setting of 4 (spa_asize_inflation = SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed its attempts to fill the pool * Create the base and nested pools with sync=disabled to speed up the "setup" phase. * Clear labels in test pool between checkpoint tests to avoid duplicate pool issues. * The import_rewind_device_replaced test has been marked as "known to fail" for the reasons listed in its DISCLAIMER. * New module parameters: zfs_spa_discard_memory_limit, zfs_remove_max_bytes_pause (not documented - debugging only) vdev_max_ms_count (formerly metaslabs_per_vdev) vdev_min_ms_count Authored by: Serapheim Dimitropoulos <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: John Kennedy <[email protected]> Reviewed by: Dan Kimmel <[email protected]> Reviewed by: Brian Behlendorf <[email protected]> Approved by: Richard Lowe <[email protected]> Ported-by: Tim Chase <[email protected]> Signed-off-by: Tim Chase <[email protected]> OpenZFS-issue: https://illumos.org/issues/9166 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8 Closes #7570
* OpenZFS 9591 - ms_shift can be incorrectly changedSerapheim Dimitropoulos2018-06-211-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ms_shift can be incorrectly changed changed in MOS config for indirect vdevs that have been historically expanded According to spa_config_update() we expect new vdevs to have vdev_ms_array equal to 0 and then we go ahead and set their metaslab size. The problem is that indirect vdevs also have vdev_ms_array == 0 because their metaslabs are destroyed once their removal is done. As a result, if a vdev was expanded and then removed may have its ms_shift changed if another vdev was added after its removal. Fortunately this behavior does not cause any type of crash or bad behavior in the kernel but it can confuse zdb and anyone doing any kind of analysis of the history of the pools. Authored by: Serapheim Dimitropoulos <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: John Kennedy <[email protected]> Reviewed by: Prashanth Sreenivasa <[email protected]> Reviewed by: Brian Behlendorf <[email protected]> Signed-off-by: Tim Chase <[email protected]> Ported-by: Tim Chase <[email protected]> OpenZFS-commit: https://github.com/openzfs/openzfs/pull/651 OpenZFS-issue: https://illumos.org/issues/9591a External-issue: DLPX-58879 Closes #7644
* zpool reopen should detect expanded devicesSara Hartse2018-05-311-2/+1
| | | | | | | | | | | | | | | | | | | | Update bdev_capacity to have wholedisk vdevs query the size of the underlying block device (correcting for the size of the efi parition and partition alignment) and therefore detect expanded space. Correct vdev_get_stats_ex so that the expandsize is aligned to metaslab size and new space is only reported if it is large enough for a new metaslab. Reviewed by: Don Brady <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed-by: Matthew Ahrens <[email protected]> Reviewed by: John Wren Kennedy <[email protected]> Signed-off-by: sara hartse <[email protected]> External-issue: LX-165 Closes #7546 Issue #7582
* Update build system and packagingBrian Behlendorf2018-05-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Minimal changes required to integrate the SPL sources in to the ZFS repository build infrastructure and packaging. Build system and packaging: * Renamed SPL_* autoconf m4 macros to ZFS_*. * Removed redundant SPL_* autoconf m4 macros. * Updated the RPM spec files to remove SPL package dependency. * The zfs package obsoletes the spl package, and the zfs-kmod package obsoletes the spl-kmod package. * The zfs-kmod-devel* packages were updated to add compatibility symlinks under /usr/src/spl-x.y.z until all dependent packages can be updated. They will be removed in a future release. * Updated copy-builtin script for in-kernel builds. * Updated DKMS package to include the spl.ko. * Updated stale AUTHORS file to include all contributors. * Updated stale COPYRIGHT and included the SPL as an exception. * Renamed README.markdown to README.md * Renamed OPENSOLARIS.LICENSE to LICENSE. * Renamed DISCLAIMER to NOTICE. Required code changes: * Removed redundant HAVE_SPL macro. * Removed _BOOT from nvpairs since it doesn't apply for Linux. * Initial header cleanup (removal of empty headers, refactoring). * Remove SPL repository clone/build from zimport.sh. * Use of DEFINE_RATELIMIT_STATE and DEFINE_SPINLOCK removed due to build issues when forcing C99 compilation. * Replaced legacy ACCESS_ONCE with READ_ONCE. * Include needed headers for `current` and `EXPORT_SYMBOL`. Reviewed-by: Tony Hutter <[email protected]> Reviewed-by: Olaf Faaland <[email protected]> Reviewed-by: Matthew Ahrens <[email protected]> Reviewed-by: Pavel Zakharov <[email protected]> Signed-off-by: Brian Behlendorf <[email protected]> TEST_ZIMPORT_SKIP="yes" Closes #7556
* OpenZFS 9189 - Add debug to vdev_label_read_config when txg check failsPavel Zakharov2018-05-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | These changes were added to help debug issue #9187. Essentially, in the original bug, vdev_validate() seems to fails in vdev_label_read_config() and prints "failed reading config". This could happen because either: 1. The labels are actually corrupt and zio_wait() fails for all of them 2. The labels were discarded because they didn't pass the txg check. Beyond 9187, having debug info when case 2 happens could be useful in other scenarios, such as zpool import. Authored by: Pavel Zakharov <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Prashanth Sreenivasa <[email protected]> Reviewed-by: Giuseppe Di Natale <[email protected]> Approved by: Matt Ahrens <[email protected]> Ported-by: Brian Behlendorf <[email protected]> OpenZFS-issue: https://illumos.org/issues/9189 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f6af1b7 Closes #7533
* OpenZFS 9187 - racing condition between vdev label and spa_last_synced_txg ↵Pavel Zakharov2018-05-141-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | in vdev_validate ztest failed with uncorrectable IO error despite having the fix for 7163. Both sides of the mirror have CANT_OPEN_BAD_LABEL, which also distinguishes it from that issue. Definitely seems like a racing condition between the vdev_validate and spa_sync: 1. Thread A (spa_sync): vdev label is updated to latest txg 2. Thread B (vdev_validate): vdev label's txg is compared to spa_last_synced_txg and is ahead. 3. Thread A (spa_sync): spa_last_synced_txg is updated to latest txg. Solution: do not check txg in vdev_validate unless config lock is held. Authored by: Pavel Zakharov <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Matt Ahrens <[email protected]> Reviewed-by: Giuseppe Di Natale <[email protected]> Approved by: Robert Mustacchi <[email protected]> Ported-by: Brian Behlendorf <[email protected]> OpenZFS-issue: https://illumos.org/issues/9187 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/805fda72 Closes #7529
* Clear vdev_faultedTim Chase2018-05-081-0/+2
| | | | | | | | | | | | | | | | | Clear vdev_faulted if ZPOOL_CONFIG_AUX_STATE is not set to "external" ZoL supports "zpool export -f" (force fault), which can be combined with "-t" (temporary fault; don't persist across export/import) and causes a MOS configuration to be set with ZPOOL_CONFIG_FAULTED=1 and without ZFS_CONFIG_AUX_STATE set at all. In this case, the previously-offlined vdev should be imported in an on-line state and. Clearing the "vdev_faulted" flag causes the import to treat the device as on-line. Typically, resilver will catch it up based on its DTL. Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Tim Chase <[email protected]> Closes #7459
* OpenZFS 9075 - Improve ZFS pool import/load process and corrupted pool recoveryPavel Zakharov2018-05-081-128/+336
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some work has been done lately to improve the debugability of the ZFS pool load (and import) process. This includes: 7638 Refactor spa_load_impl into several functions 8961 SPA load/import should tell us why it failed 7277 zdb should be able to print zfs_dbgmsg's To iterate on top of that, there's a few changes that were made to make the import process more resilient and crash free. One of the first tasks during the pool load process is to parse a config provided from userland that describes what devices the pool is composed of. A vdev tree is generated from that config, and then all the vdevs are opened. The Meta Object Set (MOS) of the pool is accessed, and several metadata objects that are necessary to load the pool are read. The exact configuration of the pool is also stored inside the MOS. Since the configuration provided from userland is external and might not accurately describe the vdev tree of the pool at the txg that is being loaded, it cannot be relied upon to safely operate the pool. For that reason, the configuration in the MOS is read early on. In the past, the two configurations were compared together and if there was a mismatch then the load process was aborted and an error was returned. The latter was a good way to ensure a pool does not get corrupted, however it made the pool load process needlessly fragile in cases where the vdev configuration changed or the userland configuration was outdated. Since the MOS is stored in 3 copies, the configuration provided by userland doesn't have to be perfect in order to read its contents. Hence, a new approach has been adopted: The pool is first opened with the untrusted userland configuration just so that the real configuration can be read from the MOS. The trusted MOS configuration is then used to generate a new vdev tree and the pool is re-opened. When the pool is opened with an untrusted configuration, writes are disabled to avoid accidentally damaging it. During reads, some sanity checks are performed on block pointers to see if each DVA points to a known vdev; when the configuration is untrusted, instead of panicking the system if those checks fail we simply avoid issuing reads to the invalid DVAs. This new two-step pool load process now allows rewinding pools accross vdev tree changes such as device replacement, addition, etc. Loading a pool from an external config file in a clustering environment also becomes much safer now since the pool will import even if the config is outdated and didn't, for instance, register a recent device addition. With this code in place, it became relatively easy to implement a long-sought-after feature: the ability to import a pool with missing top level (i.e. non-redundant) devices. Note that since this almost guarantees some loss of data, this feature is for now restricted to a read-only import. Porting notes (ZTS): * Fix 'make dist' target in zpool_import * The maximum path length allowed by tar is 99 characters. Several of the new test cases exceeded this limit resulting in them not being included in the tarball. Shorten the names slightly. * Set/get tunables using accessor functions. * Get last synced txg via the "zfs_txg_history" mechanism. * Clear zinject handlers in cleanup for import_cache_device_replaced and import_rewind_device_replaced in order that the zpool can be exported if there is an error. * Increase FILESIZE to 8G in zfs-test.sh to allow for a larger ext4 file system to be created on ZFS_DISK2. Also, there's no need to partition ZFS_DISK2 at all. The partitioning had already been disabled for multipath devices. Among other things, the partitioning steals some space from the ext4 file system, makes it difficult to accurately calculate the paramters to parted and can make some of the tests fail. * Increase FS_SIZE and FILE_SIZE in the zpool_import test configuration now that FILESIZE is larger. * Write more data in order that device evacuation take lonnger in a couple tests. * Use mkdir -p to avoid errors when the directory already exists. * Remove use of sudo in import_rewind_config_changed. Authored by: Pavel Zakharov <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: Andrew Stormont <[email protected]> Approved by: Hans Rosenfeld <[email protected]> Ported-by: Tim Chase <[email protected]> Signed-off-by: Tim Chase <[email protected]> OpenZFS-issue: https://illumos.org/issues/9075 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123 Closes #7459
* OpenZFS 8961 - SPA load/import should tell us why it failedPavel Zakharov2018-05-081-8/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Problem ======= When we fail to open or import a storage pool, we typically don't get any additional diagnostic information, just "no pool found" or "can not import". While there may be no additional user-consumable information, we should at least make this situation easier to debug/diagnose for developers and support. For example, we could start by using `zfs_dbgmsg()` to log each thing that we try when importing, and which things failed. E.g. "tried uberblock of txg X from label Y of device Z". Also, we could log each of the stages that we go through in `spa_load_impl()`. Solution ======== Following the cleanup to `spa_load_impl()`, debug messages have been added to every point of failure in that function. Additionally, debug messages have been added to strategic places, such as `vdev_disk_open()`. Authored by: Pavel Zakharov <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: Andrew Stormont <[email protected]> Approved by: Dan McDonald <[email protected]> Ported-by: Tim Chase <[email protected]> Signed-off-by: Tim Chase <[email protected]> OpenZFS-issue: https://illumos.org/issues/8961 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/418079e0 Closes #7459
* OpenZFS 9084 - spa_*_ashift must ignore spare devicesPrakash Surya2018-04-141-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's possible for the following assertion to be tripped when running ztest: assertion failed for thread 0xf09fca40, thread-id 549: spa->spa_max_ashift == spa->spa_min_ashift (0xc == 0x9), file ../../../uts/common/fs/zfs/vdev_removal.c, line 965 > $c libc.so.1`_lwp_kill+7(ebdde6c0, ebdde6c0, a9, fee7865e) libc.so.1`_assfail+0x214(ebddea28, fed7ac3c, 3c5, fef62000) libc.so.1`assfail3+0xde(fed7b130, c, 0, fed812cb, 9, 0) libzpool.so.1`spa_vdev_copy_impl+0x26b(89a4b40, ebddef74, ebddef68, 8992dc0, ebe10a00, fef073c0) libzpool.so.1`spa_vdev_remove_thread+0x6cd(87450c0, 0, 0, fee8f43a) libc.so.1`_thrp_setup+0x8c(f09fca40) libc.so.1`_lwp_start(f09fca40, 0, 0, 0, 0, 0) > ::spa -v ADDR STATE NAME 08723000 ACTIVE ztest ADDR STATE AUX DESCRIPTION 087466c0 HEALTHY - root 087450c0 HEALTHY - /rpool/tmp/ztest.0a 08745640 HEALTHY - indirect 08745bc0 HEALTHY - /rpool/tmp/ztest.2a 08746140 HEALTHY - /rpool/tmp/ztest.3a - - - spares 08744b40 HEALTHY - /rpool/tmp/ztest.spares.0 Authored by: Prakash Surya <[email protected]> Reviewed by: Prashanth Sreenivasa <[email protected]> Reviewed by: George Wilson <[email protected]> Approved by: Dan McDonald <[email protected]> Ported-by: Tim Chase <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/9084 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/18acba7 Closes #6900
* OpenZFS 9290 - device removal reduces redundancy of mirrorsMatthew Ahrens2018-04-141-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mirrors are supposed to provide redundancy in the face of whole-disk failure and silent damage (e.g. some data on disk is not right, but ZFS hasn't detected the whole device as being broken). However, the current device removal implementation bypasses some of the mirror's redundancy. Note that in no case is incorrect data returned, but we might get a checksum error when we should have been able to find the right data. There are two underlying problems: 1. When we remove a mirror device, we only read one side of the mirror. Since we can't verify the checksum, this side may be silently bad, but the good data is on the other side of the mirror (which we didn't read). This can cause the removal to "bake in" the busted data – all copies of the data in the new location are the same, busted version, while we left the good version behind. The fix for this is to read and copy both sides of the mirror. If the old and new vdevs are mirrors, we will read both sides of the old mirror, and write each copy to the corresponding side of the new mirror. (If the old and new vdevs have a different number of children, we will do this as best as possible.) Even though we aren't verifying checksums, this ensures that as long as there's a good copy of the data, we'll have a good copy after the removal, even if there's silent damage to one side of the mirror. If we're removing a mirror that has some silent damage, we'll have exactly the same damage in the new location (assuming that the new location is also a mirror). 2. When we read from an indirect vdev that points to a mirror vdev, we only consider one copy of the data. This can lead to reduced effective redundancy, because we might read a bad copy of the data from one side of the mirror, and not retry the other, good side of the mirror. Note that the problem is not with the removal process, but rather after the removal has completed (having copied correct data to both sides of the mirror), if one side of the new mirror is silently damaged, we encounter the problem when reading the relocated data via the indirect vdev. Also note that the problem doesn't occur when ZFS knows that one side of the mirror is bad, e.g. when a disk entirely fails or is offlined. The impact is that reads (from indirect vdevs that point to mirrors) may return a checksum error even though the good data exists on one side of the mirror, and scrub doesn't repair all data on the mirror (if some of it is pointed to via an indirect vdev). The fix for this is complicated by "split blocks" - one logical block may be split into two (or more) pieces with each piece moved to a different new location. In this case we need to read all versions of each split (one from each side of the mirror), and figure out which combination of versions results in the correct checksum, and then repair the incorrect versions. This ensures that we supply the same redundancy whether you use device removal or not. For example, if a mirror has small silent errors on all of its children, we can still reconstruct the correct data, as long as those errors are at sufficiently-separated offsets (specifically, separated by the largest block size - default of 128KB, but up to 16MB). Porting notes: * A new indirect vdev check was moved from dsl_scan_needs_resilver_cb() to dsl_scan_needs_resilver(), which was added to ZoL as part of the sequential scrub work. * Passed NULL for zfs_ereport_post_checksum()'s zbookmark_phys_t parameter. The extra parameter is unique to ZoL. * When posting indirect checksum errors the ABD can be passed directly, zfs_ereport_post_checksum() is not yet ABD-aware in OpenZFS. Authored by: Matthew Ahrens <[email protected]> Reviewed by: Tim Chase <[email protected]> Reviewed by: Brian Behlendorf <[email protected]> Ported-by: Tim Chase <[email protected]> OpenZFS-issue: https://illumos.org/issues/9290 OpenZFS-commit: https://github.com/openzfs/openzfs/pull/591 Closes #6900
* OpenZFS 7614, 9064 - zfs device evacuation/removalMatthew Ahrens2018-04-141-82/+268
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OpenZFS 7614 - zfs device evacuation/removal OpenZFS 9064 - remove_mirror should wait for device removal to complete This project allows top-level vdevs to be removed from the storage pool with "zpool remove", reducing the total amount of storage in the pool. This operation copies all allocated regions of the device to be removed onto other devices, recording the mapping from old to new location. After the removal is complete, read and free operations to the removed (now "indirect") vdev must be remapped and performed at the new location on disk. The indirect mapping table is kept in memory whenever the pool is loaded, so there is minimal performance overhead when doing operations on the indirect vdev. The size of the in-memory mapping table will be reduced when its entries become "obsolete" because they are no longer used by any block pointers in the pool. An entry becomes obsolete when all the blocks that use it are freed. An entry can also become obsolete when all the snapshots that reference it are deleted, and the block pointers that reference it have been "remapped" in all filesystems/zvols (and clones). Whenever an indirect block is written, all the block pointers in it will be "remapped" to their new (concrete) locations if possible. This process can be accelerated by using the "zfs remap" command to proactively rewrite all indirect blocks that reference indirect (removed) vdevs. Note that when a device is removed, we do not verify the checksum of the data that is copied. This makes the process much faster, but if it were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be possible to copy the wrong data, when we have the correct data on e.g. the other side of the mirror. At the moment, only mirrors and simple top-level vdevs can be removed and no removal is allowed if any of the top-level vdevs are raidz. Porting Notes: * Avoid zero-sized kmem_alloc() in vdev_compact_children(). The device evacuation code adds a dependency that vdev_compact_children() be able to properly empty the vdev_child array by setting it to NULL and zeroing vdev_children. Under Linux, kmem_alloc() and related functions return a sentinel pointer rather than NULL for zero-sized allocations. * Remove comment regarding "mpt" driver where zfs_remove_max_segment is initialized to SPA_MAXBLOCKSIZE. Change zfs_condense_indirect_commit_entry_delay_ticks to zfs_condense_indirect_commit_entry_delay_ms for consistency with most other tunables in which delays are specified in ms. * ZTS changes: Use set_tunable rather than mdb Use zpool sync as appropriate Use sync_pool instead of sync Kill jobs during test_removal_with_operation to allow unmount/export Don't add non-disk names such as "mirror" or "raidz" to $DISKS Use $TEST_BASE_DIR instead of /tmp Increase HZ from 100 to 1000 which is more common on Linux removal_multiple_indirection.ksh Reduce iterations in order to not time out on the code coverage builders. removal_resume_export: Functionally, the test case is correct but there exists a race where the kernel thread hasn't been fully started yet and is not visible. Wait for up to 1 second for the removal thread to be started before giving up on it. Also, increase the amount of data copied in order that the removal not finish before the export has a chance to fail. * MMP compatibility, the concept of concrete versus non-concrete devices has slightly changed the semantics of vdev_writeable(). Update mmp_random_leaf_impl() accordingly. * Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool feature which is not supported by OpenZFS. * Added support for new vdev removal tracepoints. * Test cases removal_with_zdb and removal_condense_export have been intentionally disabled. When run manually they pass as intended, but when running in the automated test environment they produce unreliable results on the latest Fedora release. They may work better once the upstream pool import refectoring is merged into ZoL at which point they will be re-enabled. Authored by: Matthew Ahrens <[email protected]> Reviewed-by: Alex Reece <[email protected]> Reviewed-by: George Wilson <[email protected]> Reviewed-by: John Kennedy <[email protected]> Reviewed-by: Prakash Surya <[email protected]> Reviewed by: Richard Laager <[email protected]> Reviewed by: Tim Chase <[email protected]> Reviewed by: Brian Behlendorf <[email protected]> Approved by: Garrett D'Amore <[email protected]> Ported-by: Tim Chase <[email protected]> Signed-off-by: Tim Chase <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/7614 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1eb Closes #6900
* Add zfs_scan_ignore_errors tunableTim Chase2018-03-131-0/+16
| | | | | | | | | When it's set, a DTL range will be cleared even if its scan/scrub had errors. This allows to work around resilver/scrub upon import when the pool has errors. Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Tim Chase <[email protected]> Closes #7293
* Hold SCL_VDEV when counting leavesOlaf Faaland2018-03-091-1/+7
| | | | | | | | | | | | A config lock should be held while vdev_count_leaves() walks the tree, otherwise the pointers reference may become invalid during the walk. SCL_VDEV is a minimal lock provided for such uses cases. Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: Tony Hutter <[email protected]> Signed-off-by: Olaf Faaland <[email protected]> Closes #7286
* Change checksum & IO delay ratelimit valuesTony Hutter2018-03-041-2/+21
| | | | | | | | | | | | | | | | Change checksum & IO delay ratelimit thresholds from 5/sec to 20/sec. This allows zed to actually trigger if a bunch of these events arrive in a short period of time (zed has a threshold of 10 events in 10 sec). Previously, if you had, say, 100 checksum errors in 1 sec, it would get ratelimited to 5/sec which wouldn't trigger zed to fault the drive. Also, convert the checksum and IO delay thresholds to module params for easy testing. Reviewed-by: loli10K <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: Giuseppe Di Natale <[email protected]> Signed-off-by: Tony Hutter <[email protected]> Closes #7252
* Extend deadman logicBrian Behlendorf2018-01-251-11/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The intent of this patch is extend the existing deadman code such that it's flexible enough to be used by both ztest and on production systems. The proposed changes include: * Added a new `zfs_deadman_failmode` module option which is used to dynamically control the behavior of the deadman. It's loosely modeled after, but independant from, the pool failmode property. It can be set to wait, continue, or panic. * wait - Wait for the "hung" I/O (default) * continue - Attempt to recover from a "hung" I/O * panic - Panic the system * Added a new `zfs_deadman_ziotime_ms` module option which is analogous to `zfs_deadman_synctime_ms` except instead of applying to a pool TXG sync it applies to zio_wait(). A default value of 300s is used to define a "hung" zio. * The ztest deadman thread has been re-enabled by default, aligned with the upstream OpenZFS code, and then extended to terminate the process when it takes significantly longer to complete than expected. * The -G option was added to ztest to print the internal debug log when a fatal error is encountered. This same option was previously added to zdb in commit fa603f82. Update zloop.sh to unconditionally pass -G to obtain additional debugging. * The FM_EREPORT_ZFS_DELAY event which was previously posted when the deadman detect a "hung" pool has been replaced by a new dedicated FM_EREPORT_ZFS_DEADMAN event. * The proposed recovery logic attempts to restart a "hung" zio by calling zio_interrupt() on any outstanding leaf zios. We may want to further restrict this to zios in either the ZIO_STAGE_VDEV_IO_START or ZIO_STAGE_VDEV_IO_DONE stages. Calling zio_interrupt() is expected to only be useful for cases when an IO has been submitted to the physical device but for some reasonable the completion callback hasn't been called by the lower layers. This shouldn't be possible but has been observed and may be caused by kernel/driver bugs. * The 'zfs_deadman_synctime_ms' default value was reduced from 1000s to 600s. * Depending on how ztest fails there may be no cache file to move. This should not be considered fatal, collect the logs which are available and carry on. * Add deadman test cases for spa_deadman() and zio_wait(). * Increase default zfs_deadman_checktime_ms to 60s. Reviewed-by: Tim Chase <[email protected]> Reviewed by: Thomas Caputi <[email protected]> Reviewed-by: Giuseppe Di Natale <[email protected]> Signed-off-by: Brian Behlendorf <[email protected]> Closes #6999
* Sequential scrub and resilversTom Caputi2017-11-151-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, scrubs and resilvers can take an extremely long time to complete. This is largely due to the fact that zfs scans process pools in logical order, as determined by each block's bookmark. This makes sense from a simplicity perspective, but blocks in zfs are often scattered randomly across disks, particularly due to zfs's copy-on-write mechanisms. This patch improves performance by splitting scrubs and resilvers into a metadata scanning phase and an IO issuing phase. The metadata scan reads through the structure of the pool and gathers an in-memory queue of I/Os, sorted by size and offset on disk. The issuing phase will then issue the scrub I/Os as sequentially as possible, greatly improving performance. This patch also updates and cleans up some of the scan code which has not been updated in several years. Reviewed-by: Brian Behlendorf <[email protected]> Authored-by: Saso Kiselkov <[email protected]> Authored-by: Alek Pinchuk <[email protected]> Authored-by: Tom Caputi <[email protected]> Signed-off-by: Tom Caputi <[email protected]> Closes #3625 Closes #6256
* Undo c89 workarounds to match with upstreamDon Brady2017-11-041-76/+38
| | | | | | | | | With PR 5756 the zfs module now supports c99 and the remaining past c89 workarounds can be undone. Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: George Melikov <[email protected]> Signed-off-by: Don Brady <[email protected]> Closes #6816
* Native Encryption for ZFS on LinuxTom Caputi2017-08-141-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This change incorporates three major pieces: The first change is a keystore that manages wrapping and encryption keys for encrypted datasets. These commands mostly involve manipulating the new DSL Crypto Key ZAP Objects that live in the MOS. Each encrypted dataset has its own DSL Crypto Key that is protected with a user's key. This level of indirection allows users to change their keys without re-encrypting their entire datasets. The change implements the new subcommands "zfs load-key", "zfs unload-key" and "zfs change-key" which allow the user to manage their encryption keys and settings. In addition, several new flags and properties have been added to allow dataset creation and to make mounting and unmounting more convenient. The second piece of this patch provides the ability to encrypt, decyrpt, and authenticate protected datasets. Each object set maintains a Merkel tree of Message Authentication Codes that protect the lower layers, similarly to how checksums are maintained. This part impacts the zio layer, which handles the actual encryption and generation of MACs, as well as the ARC and DMU, which need to be able to handle encrypted buffers and protected data. The last addition is the ability to do raw, encrypted sends and receives. The idea here is to send raw encrypted and compressed data and receive it exactly as is on a backup system. This means that the dataset on the receiving system is protected using the same user key that is in use on the sending side. By doing so, datasets can be efficiently backed up to an untrusted system without fear of data being compromised. Reviewed by: Matthew Ahrens <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: Jorgen Lundman <[email protected]> Signed-off-by: Tom Caputi <[email protected]> Closes #494 Closes #5769
* OpenZFS 6939 - add sysevents to zfs core for commandsDave Eddy2017-07-121-2/+3
| | | | | | | | | | | | | | | | | | | | Authored by: Dave Eddy <[email protected]> Reviewed by: Patrick Mooney <[email protected]> Reviewed by: Joshua M. Clulow <[email protected]> Reviewed by: Josh Wilsdon <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Richard Elling <[email protected]> Reviewed by: Alan Somers <[email protected]> Reviewed by: Andrew Stormont <[email protected]> Approved by: Matthew Ahrens <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Reviewed-by: George Melikov <[email protected]> Ported-by: Giuseppe Di Natale <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/6939 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ce1577b Closes #6328
* Force fault a vdev with 'zpool offline -f'Tony Hutter2017-05-191-6/+52
| | | | | | | | | | | | | This patch adds a '-f' option to 'zpool offline' to fault a vdev instead of bringing it offline. Unlike the OFFLINE state, the FAULTED state will trigger the FMA code, allowing for things like autoreplace and triggering the slot fault LED. The -f faults persist across imports, unless they were set with the temporary (-t) flag. Both persistent and temporary faults can be cleared with zpool clear. Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Tony Hutter <[email protected]> Closes #6094
* Skip spurious resilver IO on raidz vdevIsaac Huang2017-05-121-0/+15
| | | | | | | | | | | | | | | | On a raidz vdev, a block that does not span all child vdevs, excluding its skip sectors if any, may not be affected by a child vdev outage or failure. In such cases, the block does not need to be resilvered. However, current resilver algorithm simply resilvers all blocks on a degraded raidz vdev. Such spurious IO is not only wasteful, but also adds the risk of overwriting good data. This patch eliminates such spurious IOs. Reviewed-by: Gvozden Neskovic <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Signed-off-by: Isaac Huang <[email protected]> Closes #5316
* OpenZFS 8063 - verify that we do not attempt to access inactive txgMatthew Ahrens2017-05-101-2/+2
| | | | | | | | | | | | | | | | | | | | | Authored by: Matthew Ahrens <[email protected]> Reviewed by: Serapheim Dimitropoulos <[email protected]> Reviewed by: Pavel Zakharov <[email protected]> Approved by: Robert Mustacchi <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Ported-by: George Melikov <[email protected]> A standard practice in ZFS is to keep track of "per-txg" state. Any of the 3 active TXG's (open, quiescing, syncing) can have different values for this state. We should assert that we do not attempt to modify other (inactive) TXG's. Porting Notes: - ASSERTV added to txg_sync_waiting() for unused variable. OpenZFS-issue: https://www.illumos.org/issues/8063 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/01acb46 Closes #6109
* OpenZFS 8166 - zpool scrub thinks it repaired offline deviceMatthew Ahrens2017-05-101-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | Authored by: Matthew Ahrens <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed-by: loli10K <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Ported-by: Matthew Ahrens <[email protected]> If we do a scrub while a leaf device is offline (via "zpool offline"), we will inadvertently clear the DTL (dirty time log) of the offline device, even though it is still damaged. When the device comes back online, we will incompletely resilver it, thinking that the scrub repaired blocks written before the scrub was started. The incomplete resilver can lead to data loss if there is a subsequent failure of a different leaf device. The fix is to never clear the DTL of offline devices. Note that if a device is onlined while a scrub is in progress, the scrub will be restarted. The problem can be worked around by running "zpool scrub" after "zpool online". OpenZFS-issue: https://www.illumos.org/issues/8166 OpenZFS-commit: https://github.com/openzfs/openzfs/pull/372 Closes #5806 Closes #6103
* Add missing *_destroy/*_fini callsGvozden Neskovic2017-05-041-0/+3
| | | | | | | | | The proposed debugging enhancements in zfsonlinux/spl#587 identified the following missing *_destroy/*_fini calls. Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Gvozden Neskovic <[email protected]> Closes #5428
* Write label 2,3 uberblocks when vdev expandsOlaf Faaland2017-05-021-0/+7
| | | | | | | | | | | | | | | | | | | | | | When vdev_psize increases, the location of labels 2 and 3 changes because their location is relative to the end of the device. The configs for labels 2 and 3 are written during the next spa_sync() because the vdev is added to the dirty config list. However, the uberblock rings are not re-written in their new location, leaving the device vulnerable to the beginning of the device being overwritten or damaged. This patch copies the uberblock ring from label 0 to labels 2 and 3, in their new locations, at the next sync after vdev_psize increases. Also, add a test zpool_expand_004_pos.ksh to confirm the uberblocks are copied. Reviewed-by: BearBabyLiu <[email protected]> Reviewed-by: Andreas Dilger <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Olaf Faaland <[email protected]> Closes #5108
* OpenZFS 7786 - zfs`vdev_online() needs better notification about state changesYuri Pankov2017-05-011-6/+8
| | | | | | | | | | | | | | Authored by: Yuri Pankov <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: George Wilson <[email protected]> Approved by: Albert Lee <[email protected]> Reviewed-by: Giuseppe Di Natale <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Ported-by: bunder2015 <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/7786 OpenZFS-commit: http://github.com/openzfs/openzfs/commit/db8498f Closes #6074
* OpenZFS 5120 - zfs should allow large block/gzip/raidz boot pool (loader ↵Brian Behlendorf2017-04-131-18/+6
| | | | | | | | | | | | | | | | | | | | | | | project) Authored by: Toomas Soome <[email protected]> Reviewed by: George Wilson <[email protected]> Reviewed by: Yuri Pankov <[email protected]> Reviewed by: Andrew Stormont <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Approved by: Robert Mustacchi <[email protected]> Reviewed-by: Giuseppe Di Natale <[email protected]> Reviewed-by: George Melikov <[email protected]> Reviewed-by: Don Brady <[email protected]> Ported-by: Brian Behlendorf <[email protected]> Porting Notes: - grub-2.02-beta2-422-gcad5cc0 includes support for large blocks. - Commit 8aab121 allowed GZIP[1-9]. - Grub allows pools with multiple top-level vdevs. OpenZFS-issue: https://www.illumos.org/issues/5120 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c8811bd Closes #6007
* OpenZFS 7885 - zpool list can report 16.0e for expandszSteven Hartland2017-04-051-8/+18
| | | | | | | | | | | | | | | | | | | | | | | | | Authored by: Steven Hartland <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: George Wilson <[email protected]> Approved by: Gordon Ross <[email protected]> When a member of a RAIDZ has been replaced with a device smaller than the original, then the top level vdev can report its expand size as 16.0E. The reduced child asize causes the RAIDZ to have a vdev_asize lower than its vdev_max_asize which then results in an underflow during the calculation of the parents expand size. Fix this by updating the vdev_asize if it shrinks, which is already protected by a check against vdev_min_asize so should always be safe. Also for RAIDZ vdevs, ensure that the sum of their child vdev_min_asize is always greater than the parents vdev_min_size. Reviewed-off-by: Brian Behlendorf <[email protected]> Ported-by: George Melikov <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/7885 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/bb0dbaa Closes #5963
* Check ashift validity in 'zpool add'LOLi2017-03-281-2/+12
| | | | | | | | | | | | | df83110 added the ability to specify a custom "ashift" value from the command line in 'zpool add' and 'zpool attach'. This commit adds additional checks to the provided ashift to prevent invalid values from being used, which could result in disastrous consequences for the whole pool. Additionally provide ASHIFT_MAX and ASHIFT_MIN definitions in spa.h. Reviewed-by: Giuseppe Di Natale <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: loli10K <[email protected]> Closes #5878
* OpenZFS 7072 - zfs fails to expand if lun added when os is in shutdown stateGeorge Melikov2017-02-011-0/+12
| | | | | | | | | | | | | | | | | | | Authored by: George Wilson <[email protected]> Reviewed by: Igor Kozhukhov <[email protected]> Reviewed by: Dan Kimmel <[email protected]> Reviewed by: Matthew Ahrens <[email protected]> Reviewed by: Prakash Surya <[email protected]> Reviewed by: Alex Reece <[email protected]> Approved by: Dan McDonald <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Ported-by: George Melikov <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/7072 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c39a2aa Closes #5694 Porting notes: - vdev.c: 'vdev_get_stats' changes are moved to 'vdev_get_stats_ex'. - vdev_disk.c: ignored, Linux specific code is different.
* OpenZFS 5561 - support root pools on EFI/GPT partitioned disksBrian Behlendorf2017-01-271-3/+1
| | | | | | | | | | | Reviewed by: Jean McCormack <[email protected]> Reviewed by: Josef 'Jeff' Sipek <[email protected]> Approved by: Dan McDonald <[email protected]> Reviewed-by: George Melikov <[email protected]> Ported-by: Brian Behlendorf <[email protected]> OpenZFS-issue: https://www.illumos.org/issues/5561 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1a902ef Closes #5672
* codebase style improvements for OpenZFS 6459 portGeorge Melikov2017-01-221-1/+2
|
* Fix spellingka72017-01-031-1/+1
| | | | | | | | | Reviewed-by: Brian Behlendorf <[email protected] Reviewed-by: Giuseppe Di Natale <[email protected]>> Reviewed-by: George Melikov <[email protected]> Reviewed-by: Haakan T Johansson <[email protected]> Closes #5547 Closes #5543
* DLPX-44812 integrate EP-220 large memory scalabilityDavid Quigley2016-11-291-5/+6
|
* Add illumos FMD ZFS logic to ZED -- phase 2Don Brady2016-11-071-0/+11
| | | | | | | | | | | | | | | | | | | | | | | The phase 2 work primarily entails the Diagnosis Engine and the Retire Agent modules. It also includes infrastructure to support a crude FMD environment to host these modules. The Diagnosis Engine consumes I/O and checksum ereports and feeds them into a SERD engine which will generate a corres- ponding fault diagnosis when the SERD engine fires. All the diagnosis state data is collected into cases, one case per vdev being tracked. The Retire Agent responds to diagnosed faults by isolating the faulty VDEV. It will notify the ZFS kernel module of the new VDEV state (degraded or faulted). This agent is also responsible for managing hot spares across pools. When it encounters a device fault or a device removal it replaces the device with an appropriate spare if available. Reviewed-by: Tony Hutter <[email protected]> Reviewed-by: Brian Behlendorf <[email protected]> Signed-off-by: Don Brady <[email protected]> Closes #5343
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-29 17:34:25 +0000