| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For a long time now the kernel has been moving away from using the
pdflush daemon to write 'old' dirty pages to disk. The primary reason
for this is because the pdflush daemon is single threaded and can be
a limiting factor for performance. Since pdflush sequentially walks
the dirty inode list for each super block any delay in processing can
slow down dirty page writeback for all filesystems.
The replacement for pdflush is called bdi (backing device info). The
bdi system involves creating a per-filesystem control structure each
with its own private sets of queues to manage writeback. The advantage
is greater parallelism which improves performance and prevents a single
filesystem from slowing writeback to the others.
For a long time both systems co-existed in the kernel so it wasn't
strictly required to implement the bdi scheme. However, as of
Linux 2.6.36 kernels the pdflush functionality has been retired.
Since ZFS already bypasses the page cache for most I/O this is only
an issue for mmap(2) writes which must go through the page cache.
Even then adding this missing support for newer kernels was overlooked
because there are other mechanisms which can trigger writeback.
However, there is one critical case where not implementing the bdi
functionality can cause problems. If an application handles a page
fault it can enter the balance_dirty_pages() callpath. This will
result in the application hanging until the number of dirty pages in
the system drops below the dirty ratio.
Without a registered backing_device_info for the filesystem the
dirty pages will not get written out. Thus the application will hang.
As mentioned above this was less of an issue with older kernels because
pdflush would eventually write out the dirty pages.
This change adds a backing_device_info structure to the zfs_sb_t
which is already allocated per-super block. It is then registered
when the filesystem mounted and unregistered on unmount. It will
not be registered for mounted snapshots which are read-only. This
change will result in flush-<pool> thread being dynamically created
and destroyed per-mounted filesystem for writeback.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #174
|
| |
|
|
|
|
|
|
| |
This should simplify the code a bit by re-using existing code
to fork and exec a process.
Signed-off-by: Brian Behlendorf <[email protected]>
Issue #190
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
At the moment we call exportfs -v every time we check whether an
NFS share is active. This happens every time you run a zfs or
zpool command, making them extremely slow when you have a lot of
exports. The time taken is approx O(n2) of the number of shares.
This commit stores the output from exportfs -v in a temporary file
and use this to speed up subsequent accesses.
This mechanism is still too slow - if you have tens of thousands
of NFS shares it will still be painful running ANY zfs/zpool
command.
Signed-off-by: Gunnar Beutner <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #341
|
| |
|
|
|
|
|
|
|
|
|
| |
Unlike most other Linux distributions archlinux installs its
init scripts in /etc/rc.d insead of /etc/init.d. This commit
provides an archlinux rc.d script for zfs and extends the
build infrastructure to ensure it get's installed in the
correct place.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #322
|
|
|
The sharenfs and sharesmb properties depend on the libshare library
to export datasets via NFS and SMB. This commit implements the base
libshare functionality as well as support for managing NFS shares.
Signed-off-by: Brian Behlendorf <[email protected]>
|
