| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
| |
Reviewed-by: Ryan Moeller <[email protected]>
Reviewed-by: Richard Laager <[email protected]>
Reviewed-by: Brian Behlendorf <[email protected]>
Signed-off-by: Andrea Gelmini <[email protected]>
Closes #9234
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add an 'enclosure_symlinks' option to vdev_id.conf. This creates
consistently named symlinks to the enclosure devices (/dev/sg*) based
off the configuration in vdev_id.conf. The enclosure symlinks show
up in /dev/by-enclosure/<prefix>-<channel><num>. The links make it
make it easy to run sg_ses on a particular enclosure device. The
enclosure links are created in addition to the normal
/dev/disk/by-vdev links.
'enclosure_symlinks' is only valid in sas_direct configurations.
Reviewed-by: Brian Behlendorf <[email protected]>
Reviewed-by: Simon Guest <[email protected]>
Signed-off-by: Tony Hutter <[email protected]>
Closes #8194
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This extends vdev_id to support a new slot type, ses, for SCSI Enclosure
Services. With slot type ses, the disk slot numbers are determined by
using the device slot number reported by sg_ses for the device with
matching SAS address, found by querying all available enclosures.
This is primarily of use on systems with a deficient driver omitting
support for bay_identifier in /sys/devices. In my testing, I found that
the existing slot types of port and id were not stable across disk
replacement, so an alternative was required.
Reviewed-by: Brian Behlendorf <[email protected]>
Signed-off-by: Simon Guest <[email protected]>
Closes #6956
|
| |
|
|
|
|
|
|
|
|
| |
On systems with SCSI rather than SAS disk topology, this change enables
the vdev_id script to match against the block device path, and therefore
create a vdev alias in /dev/disk/by-vdev.
Reviewed-by: Tony Hutter <[email protected]>
Reviewed-by: Brian Behlendorf <[email protected]>
Signed-off-by: Simon Guest <[email protected]>
Closes #6592
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
With HPE hardware and hpsa-driven SAS adapters, only a single phy is
reported, but no individual per-port phys (ie. no phy* entry below
port_dir), which breaks topology detection in the current sas_handler
code. Instead, slot information can be derived directly from the port
number. This change implements a new slot keyword "port" similar to
"id" and "lun", and assumes a default phy/port of 0 if no individual
phy entry can be found. It allows to use the "sas_direct" topology with
current HPE Dxxxx and Apollo 45xx JBODs.
Reviewed-by: Brian Behlendorf <[email protected]>
Signed-off-by: Daniel Kobras <[email protected]>
Closes #6484
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Udev may fail to create the expected symbolic links in
/dev/disk/by-vdev on systems with the
device-mapper-multipath-0.4.9-100.el6 package installed. This affects
RHEL 6.9 and possibly other downstream distributions.
That version of the multipath command may incorrectly list a drive
state as "unkown" instead of "running". The issue was introduced
in the patch for https://bugzilla.redhat.com/show_bug.cgi?id=1401769
The vdev_id udev helper uses the state reported by "multipath -l" to
detect an online component disk of a multipath device in order to
resolve its physical slot and enclosure. Changing the command
invocation to "multipath -ll" works around the above issue by causing
multipath to consult additional sources of information to determine
the drive state.
Reviewed-by: Tony Hutter <[email protected]>
Reviewed-by: Brian Behlendorf <[email protected]>
Reviewed-by: Giuseppe Di Natale <[email protected]>
Signed-off-by: Ned Bass <[email protected]>
Closes #6039
|
| |
|
|
|
|
|
|
|
|
|
| |
Add new keyword 'slot' to vdev_id.conf
This selects from where to get the slot number for a SAS/SATA disk
Needed to enable access to the physical position of a disk in a
Supermicro 2027R-AR24NV .
Signed-off-by: Brian Behlendorf <[email protected]>
Signed-off-by: Ned Bass <[email protected]>
Closes #3693
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Slot mapping in vdev_id doesn't work on systems using mawk as the 'awk'
alternative. A regular expression in map_slot() contains an unquoted
empty string following the alternation (|) operator, which results in an
"missing operand" error with mawk. The solution is to rearrange the
expression so the alternation has two operands.
Signed-off-by: Ned Bass <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes zfsonlinux/pkg-zfs#136
Closes zfsonlinux/zfs#2965
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The vdev_id udev helper currently applies slot renumbering rules to
every channel (JBOD) in the system. This is too inflexible for systems
with non-homogeneous storage topologies. The "slot" keyword now takes
an optional third parameter which names a channel to which the mapping
will apply. If the third parameter is omitted then the rule applies to
all channels. The first-specified rule that can match a slot takes
precedence. Therefore a channel-specific rule for a given slot should
generally appear before a generic rule for the same slot number. In
this way a custom slot mapping can be applied to a particular channel
and a default mapping applied to the rest.
Signed-off-by: Ned Bass <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #2056
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The bug is caused by multipath output like this:
35000c50056bd77a7 dm-15 HP,MB3000FCWDH
size=2.7T features='0' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=0 status=active
| `- 2:0:16:0 sdq 65:0 active undef running
`-+- policy='round-robin 0' prio=0 status=enabled
`- 4:0:52:0 sdfp 130:176 active undef running
Note that the pipe symbols mean that the field numbering is different
between the sdq and sdfp lines. The fix edits out the pipe symbols.
Signed-off-by: Ned Bass <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #1692
|
| |
|
|
|
|
|
|
|
|
|
| |
The vdev_id udev helper strictly requires configuration file keywords
to always be anchored at the beginning of the line and to be followed
by a space character. However, users may prefer to use indentation or
tab delimitation. Improve flexibility by simply requiring a keyword
to be the first field on the line.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #1239
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add a vdev_id feature to map device names based on already defined
udev device links. To increase the odds that vdev_id will run after
the rules it depends on, increase the vdev.rules rule number from 60
to 69. With this change, vdev_id now provides functionality analogous
to zpool_id and zpool_layout, paving the way to retire those tools.
A defined alias takes precedence over a topology-derived name, but the
two naming methods can otherwise coexist. For example, one might name
drives in a JBOD with the sas_direct topology while naming an internal
L2ARC device with an alias.
For example, the following lines in vdev_id.conf will result in the
creation of links /dev/disk/by-vdev/{d1,d2}, each pointing to the same
target as the device link specified in the third field.
# by-vdev
# name fully qualified or base name of device link
alias d1 /dev/disk/by-id/wwn-0x5000c5002de3b9ca
alias d2 wwn-0x5000c5002def789e
Also perform some minor vdev_id cleanup, such as removal of the unused
-s command line option.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #981
|
| |
|
|
|
|
|
|
|
|
|
|
| |
While expanding positional parameters shell requires non-single
digits to be enclosed in braces. When the SAS topology is
non-trivial the number of positional parameters generated internally
by vdev_id script (using set -- ...) easily crosses single digit limit
and vdev_id fails to generate links.
Signed-off-by: Ned Bass <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #1119
|
| |
|
|
|
|
|
|
|
|
|
| |
Full bash may not be available in all environments where udev helpers
run, such as in an initial ramdisk. To avoid breakage in this case,
remove use of bash-specific features such as variable arrays and the
`declare' keyword from the vdev_id script.
Signed-off-by: Ned Bass <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #870
|
| |
|
|
|
|
|
|
| |
Remove all of the generated autotools products from the repository
and update the .gitignore files accordingly.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #718
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.
In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).
With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #862
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict(). This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.
However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics. This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.
Signed-off-by: Richard Yao <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #784
|
| |
|
|
|
|
|
|
|
| |
The vmtruncate_range() support has been removed from the kernel in
favor of using the fallocate method in the file_operations table.
Signed-off-by: Richard Yao <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Issue #784
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes. This interface used to
take the child dentry and a bool describing if the parent is needed.
NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.
Signed-off-by: Richard Yao <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Issue #784
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.
This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.
Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.
This change also depends on API changes which are available in 2.6.37
and latter kernels. The build system has been updated to detect this,
but there is no compatibility mode for older kernels. This means that
online expansion will NOT be available in older kernels. However, it
will still be possible to expand the vdev offline.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #808
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
torvalds/linux@adc0e91ab142abe93f5b0d7980ada8a7676231fe introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:
error: implicit declaration of function 'd_alloc_root'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current d_make_root()
interface for readability. Then we introduce an autotools check
to determine if d_make_root() is available. If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.
Signed-off-by: Richard Yao <[email protected]>
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #776
|
|
|
vdev_id parses the file /etc/zfs/vdev_id.conf to map a physical path
in a storage topology to a channel name. The channel name is combined
with a disk enclosure slot number to create an alias that reflects the
physical location of the drive. This is particularly helpful when it
comes to tasks like replacing failed drives. Slot numbers may also be
re-mapped in case the default numbering is unsatisfactory. The drive
aliases will be created as symbolic links in /dev/disk/by-vdev.
The only currently supported topologies are sas_direct and sas_switch:
o sas_direct - a channel is uniquely identified by a PCI slot and a
HBA port
o sas_switch - a channel is uniquely identified by a SAS switch port
A multipath mode is supported in which dm-mpath devices are handled by
examining the first running component disk, as reported by 'multipath
-l'. In multipath mode the configuration file should contain a
channel definition with the same name for each path to a given
enclosure.
vdev_id can replace the existing zpool_id script on systems where the
storage topology conforms to sas_direct or sas_switch. The script
could be extended to support other topologies as well. The advantage
of vdev_id is that it is driven by a single static input file that can
be shared across multiple nodes having a common storage toplogy.
zpool_id, on the other hand, requires a unique /etc/zfs/zdev.conf per
node and a separate slot-mapping file. However, zpool_id provides the
flexibility of using any device names that show up in
/dev/disk/by-path, so it may still be needed on some systems.
vdev_id's functionality subsumes that of the sas_switch_id script, and
it is unlikely that anyone is using it, so sas_switch_id is removed.
Finally, /dev/disk/by-vdev is added to the list of directories that
'zpool import' will scan.
Signed-off-by: Brian Behlendorf <[email protected]>
Closes #713
|
