diff options
| -rw-r--r-- | man/man5/zfs-module-parameters.5 | 34 |
1 files changed, 17 insertions, 17 deletions
diff --git a/man/man5/zfs-module-parameters.5 b/man/man5/zfs-module-parameters.5 index 4dbf7d766..316373d79 100644 --- a/man/man5/zfs-module-parameters.5 +++ b/man/man5/zfs-module-parameters.5 @@ -94,7 +94,7 @@ Default value: \fB2\fR. Scales \fBl2arc_headroom\fR by this percentage when L2ARC contents are being successfully compressed before writing. A value of 100 disables this feature. .sp -Default value: \fB200\fR. +Default value: \fB200\fR%. .RE .sp @@ -436,7 +436,7 @@ Percentage that can be consumed by dnodes of ARC meta buffers. See also \fBzfs_arc_dnode_limit\fR which serves a similar purpose but has a higher priority if set to nonzero value. .sp -Default value: \fB10\fR. +Default value: \fB10\fR%. .RE .sp @@ -449,7 +449,7 @@ Percentage of ARC dnodes to try to scan in response to demand for non-metadata when the number of bytes consumed by dnodes exceeds \fBzfs_arc_dnode_limit\fR. .sp -Default value: \fB10% of the number of dnodes in the ARC\fR. +Default value: \fB10\fR% of the number of dnodes in the ARC. .RE .sp @@ -503,7 +503,7 @@ Default value: \fB0\fR. Throttle I/O when free system memory drops below this percentage of total system memory. Setting this value to 0 will disable the throttle. .sp -Default value: \fB10\fR. +Default value: \fB10\fR%. .RE .sp @@ -566,7 +566,7 @@ See also \fBzfs_arc_meta_limit\fR which serves a similar purpose but has a higher priority if set to nonzero value. .sp -Default value: \fB75\fR. +Default value: \fB75\fR%. .RE .sp @@ -748,7 +748,7 @@ zfs_arc_min if necessary. This value is specified as percent of pagecache size (as measured by NR_FILE_PAGES) where that percent may exceed 100. This only operates during memory pressure/reclaim. .sp -Default value: \fB0\fR (disabled). +Default value: \fB0\fR% (disabled). .RE .sp @@ -787,7 +787,7 @@ stable storage. The timeout is scaled based on a percentage of the last lwb latency to avoid significantly impacting the latency of each individual transaction record (itx). .sp -Default value: \fB5\fR. +Default value: \fB5\fR%. .RE .sp @@ -894,7 +894,7 @@ expressed as a percentage of \fBzfs_dirty_data_max\fR. This value should be >= zfs_vdev_async_write_active_max_dirty_percent. See the section "ZFS TRANSACTION DELAY". .sp -Default value: \fB60\fR. +Default value: \fB60\fR%. .RE .sp @@ -943,7 +943,7 @@ writes are halted until space frees up. This parameter takes precedence over \fBzfs_dirty_data_max_percent\fR. See the section "ZFS TRANSACTION DELAY". .sp -Default value: 10 percent of all memory, capped at \fBzfs_dirty_data_max_max\fR. +Default value: \fB10\fR% of physical RAM, capped at \fBzfs_dirty_data_max_max\fR. .RE .sp @@ -958,7 +958,7 @@ This limit is only enforced at module load time, and will be ignored if precedence over \fBzfs_dirty_data_max_max_percent\fR. See the section "ZFS TRANSACTION DELAY". .sp -Default value: 25% of physical RAM. +Default value: \fB25\fR% of physical RAM. .RE .sp @@ -973,7 +973,7 @@ time, and will be ignored if \fBzfs_dirty_data_max\fR is later changed. The parameter \fBzfs_dirty_data_max_max\fR takes precedence over this one. See the section "ZFS TRANSACTION DELAY". .sp -Default value: \fB25\fR. +Default value: \fB25\fR%. .RE .sp @@ -987,7 +987,7 @@ memory. Once this limit is exceeded, new writes are halted until space frees up. The parameter \fBzfs_dirty_data_max\fR takes precedence over this one. See the section "ZFS TRANSACTION DELAY". .sp -Default value: 10%, subject to \fBzfs_dirty_data_max_max\fR. +Default value: \fB10\fR%, subject to \fBzfs_dirty_data_max_max\fR. .RE .sp @@ -1080,7 +1080,7 @@ When the pool has more than the dirty data is between min and max, the active I/O limit is linearly interpolated. See the section "ZFS I/O SCHEDULER". .sp -Default value: \fB60\fR. +Default value: \fB60\fR%. .RE .sp @@ -1095,7 +1095,7 @@ When the pool has less than the dirty data is between min and max, the active I/O limit is linearly interpolated. See the section "ZFS I/O SCHEDULER". .sp -Default value: \fB30\fR. +Default value: \fB30\fR%. .RE .sp @@ -1227,7 +1227,7 @@ will tend to be slower than empty devices. See also \fBzio_dva_throttle_enabled\fR. .sp -Default value: \fB1000\fR. +Default value: \fB1000\fR%. .RE .sp @@ -1882,7 +1882,7 @@ Default value: \fB2\fR. This controls the number of threads used by the dp_sync_taskq. The default value of 75% will create a maximum of one thread per cpu. .sp -Default value: \fB75\fR. +Default value: \fB75\fR%. .RE .sp @@ -2161,7 +2161,7 @@ Default value: \fB1024\fR. This controls the number of threads used by the dp_zil_clean_taskq. The default value of 100% will create a maximum of one thread per cpu. .sp -Default value: \fB100\fR. +Default value: \fB100\fR%. .RE .sp |