diff options
Diffstat (limited to 'src/mesa/drivers')
| -rw-r--r-- | src/mesa/drivers/dri/i965/brw_fs.cpp | 124 |
1 files changed, 104 insertions, 20 deletions
diff --git a/src/mesa/drivers/dri/i965/brw_fs.cpp b/src/mesa/drivers/dri/i965/brw_fs.cpp index 4666fa5ea9a..b1cd0d959fb 100644 --- a/src/mesa/drivers/dri/i965/brw_fs.cpp +++ b/src/mesa/drivers/dri/i965/brw_fs.cpp @@ -4618,6 +4618,108 @@ fs_visitor::lower_logical_sends() } /** + * Get the closest allowed SIMD width for instruction \p inst accounting for + * some common regioning and execution control restrictions that apply to FPU + * instructions. These restrictions don't necessarily have any relevance to + * instructions not executed by the FPU pipeline like extended math, control + * flow or send message instructions. + * + * For virtual opcodes it's really up to the instruction -- In some cases + * (e.g. where a virtual instruction unrolls into a simple sequence of FPU + * instructions) it may simplify virtual instruction lowering if we can + * enforce FPU-like regioning restrictions already on the virtual instruction, + * in other cases (e.g. virtual send-like instructions) this may be + * excessively restrictive. + */ +static unsigned +get_fpu_lowered_simd_width(const struct brw_device_info *devinfo, + const fs_inst *inst) +{ + /* Maximum execution size representable in the instruction controls. */ + unsigned max_width = MIN2(32, inst->exec_size); + + /* According to the PRMs: + * "A. In Direct Addressing mode, a source cannot span more than 2 + * adjacent GRF registers. + * B. A destination cannot span more than 2 adjacent GRF registers." + * + * Look for the source or destination with the largest register region + * which is the one that is going to limit the overall execution size of + * the instruction due to this rule. + */ + unsigned reg_count = inst->regs_written; + + for (unsigned i = 0; i < inst->sources; i++) + reg_count = MAX2(reg_count, (unsigned)inst->regs_read(i)); + + /* Calculate the maximum execution size of the instruction based on the + * factor by which it goes over the hardware limit of 2 GRFs. + */ + if (reg_count > 2) + max_width = MIN2(max_width, inst->exec_size / DIV_ROUND_UP(reg_count, 2)); + + /* According to the IVB PRMs: + * "When destination spans two registers, the source MUST span two + * registers. The exception to the above rule: + * + * - When source is scalar, the source registers are not incremented. + * - When source is packed integer Word and destination is packed + * integer DWord, the source register is not incremented but the + * source sub register is incremented." + * + * The hardware specs from Gen4 to Gen7.5 mention similar regioning + * restrictions. The code below intentionally doesn't check whether the + * destination type is integer because empirically the hardware doesn't + * seem to care what the actual type is as long as it's dword-aligned. + */ + if (devinfo->gen < 8) { + for (unsigned i = 0; i < inst->sources; i++) { + if (inst->regs_written == 2 && + inst->regs_read(i) != 0 && inst->regs_read(i) != 2 && + !is_uniform(inst->src[i]) && + !(type_sz(inst->dst.type) == 4 && inst->dst.stride == 1 && + type_sz(inst->src[i].type) == 2 && inst->src[i].stride == 1)) + max_width = MIN2(max_width, inst->exec_size / + inst->regs_written); + } + } + + /* From the IVB PRMs: + * "When an instruction is SIMD32, the low 16 bits of the execution mask + * are applied for both halves of the SIMD32 instruction. If different + * execution mask channels are required, split the instruction into two + * SIMD16 instructions." + * + * There is similar text in the HSW PRMs. Gen4-6 don't even implement + * 32-wide control flow support in hardware and will behave similarly. + */ + if (devinfo->gen < 8 && !inst->force_writemask_all) + max_width = MIN2(max_width, 16); + + /* From the IVB PRMs (applies to HSW too): + * "Instructions with condition modifiers must not use SIMD32." + * + * From the BDW PRMs (applies to later hardware too): + * "Ternary instruction with condition modifiers must not use SIMD32." + */ + if (inst->conditional_mod && (devinfo->gen < 8 || inst->is_3src(devinfo))) + max_width = MIN2(max_width, 16); + + /* From the IVB PRMs (applies to other devices that don't have the + * brw_device_info::supports_simd16_3src flag set): + * "In Align16 access mode, SIMD16 is not allowed for DW operations and + * SIMD8 is not allowed for DF operations." + */ + if (inst->is_3src(devinfo) && !devinfo->supports_simd16_3src) + max_width = MIN2(max_width, inst->exec_size / reg_count); + + /* Only power-of-two execution sizes are representable in the instruction + * control fields. + */ + return 1 << _mesa_logbase2(max_width); +} + +/** * Get the closest native SIMD width supported by the hardware for instruction * \p inst. The instruction will be left untouched by * fs_visitor::lower_simd_width() if the returned value is equal to the @@ -4661,26 +4763,8 @@ get_lowered_simd_width(const struct brw_device_info *devinfo, case BRW_OPCODE_SAD2: case BRW_OPCODE_MAD: case BRW_OPCODE_LRP: - case FS_OPCODE_PACK: { - /* According to the PRMs: - * "A. In Direct Addressing mode, a source cannot span more than 2 - * adjacent GRF registers. - * B. A destination cannot span more than 2 adjacent GRF registers." - * - * Look for the source or destination with the largest register region - * which is the one that is going to limit the overal execution size of - * the instruction due to this rule. - */ - unsigned reg_count = inst->regs_written; - - for (unsigned i = 0; i < inst->sources; i++) - reg_count = MAX2(reg_count, (unsigned)inst->regs_read(i)); - - /* Calculate the maximum execution size of the instruction based on the - * factor by which it goes over the hardware limit of 2 GRFs. - */ - return inst->exec_size / DIV_ROUND_UP(reg_count, 2); - } + case FS_OPCODE_PACK: + return get_fpu_lowered_simd_width(devinfo, inst); case SHADER_OPCODE_RCP: case SHADER_OPCODE_RSQ: |