From dfab1ce11c784b99e257acfb439c79936f9cf17b Mon Sep 17 00:00:00 2001 From: Damiano Galassi Date: Sat, 6 Aug 2016 12:36:17 +0200 Subject: MacGui: small UI tweaks. --- macosx/English.lproj/Video.xib | 327 ++++++++++++++++++++++++++--------------- 1 file changed, 206 insertions(+), 121 deletions(-) (limited to 'macosx/English.lproj/Video.xib') diff --git a/macosx/English.lproj/Video.xib b/macosx/English.lproj/Video.xib index 17f560460..cfaf76f38 100644 --- a/macosx/English.lproj/Video.xib +++ b/macosx/English.lproj/Video.xib @@ -1,15 +1,15 @@ - - + + - + - + @@ -24,12 +24,11 @@ - + - - - + + @@ -39,10 +38,12 @@ - - - + + Set the average bitrate. The instantaneous bitrate can be much higher or lower at any point in time. But the average over a long duration will be the value set here. If you need to limit instantaneous bitrate, look into x264's vbv-bufsize and vbv-maxrate settings. + + + @@ -78,10 +79,9 @@ - - - - + + + @@ -92,9 +92,8 @@ - - - + + Output framerate. 'Same as source' variable framerate is recommended. Peak framerate is 'same as source' VFR with a peak rate. VFR is incompatible with some players. @@ -121,9 +120,8 @@ - - - - - + + + + + @@ -214,9 +213,8 @@ - - - + + @@ -226,9 +224,8 @@ - - - + + @@ -238,9 +235,11 @@ - - - + + + + + @@ -271,9 +270,12 @@ - - - + + + + + + @@ -302,19 +304,8 @@ - - - - - - - - - - - - - + + Set the desired quality factor. The encoder targets a certain quality. The scale used by each video encoder is different.
x264's scale is logarithmic and lower values coorespond to higher quality. So small decreases in value will result in progressively larger increases in the resulting file size. A value of 0 means lossless and will result in a file size that is larger than the original source, unless the source was also lossless.
FFmpeg and Theora's scales are more linear. These encoders do not have a lossless mode. @@ -340,9 +331,8 @@ - - - + + @@ -353,29 +343,59 @@ + + + + + + + - + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + - + - - - - Adjust encoder settings to trade off compression efficiency against encoding speed. - -This estabilishes your default encoder settings. Tunes, profiles, levels and advances option string will be applied to this. -You should generally set this option to the slowest you can bear since slower settings will result in better quality or smaller files. - - - - - - - - - + + @@ -385,9 +405,8 @@ You should generally set this option to the slowest you can bear since slower se - - - + + @@ -397,9 +416,8 @@ You should generally set this option to the slowest you can bear since slower se - - - + + @@ -409,9 +427,8 @@ You should generally set this option to the slowest you can bear since slower se - - - + + @@ -421,9 +438,8 @@ You should generally set this option to the slowest you can bear since slower se - - - + + Tune settings to optimize for common scenarios. This can improve efficiency for particular source characteristics or set characteristics of the output file. Changes will be applied after the preset but before all other parameters. @@ -443,9 +459,8 @@ This can improve efficiency for particular source characteristics or set charact - - - + + Sets and ensures compliance with the specified profile. Overrides all other settings. @@ -464,9 +479,8 @@ Overrides all other settings. - - - + + @@ -483,9 +497,8 @@ Overrides all other settings. - - - - + + @@ -514,9 +526,11 @@ Set this if your device is struggling to play the output (dropped frames). - - - + + + + + @@ -527,9 +541,11 @@ Set this if your device is struggling to play the output (dropped frames). - - - + + + + + @@ -540,9 +556,8 @@ Set this if your device is struggling to play the output (dropped frames). - - - - + + + + + @@ -568,9 +585,8 @@ Set this if your device is struggling to play the output (dropped frames). - - - + + @@ -580,23 +596,83 @@ Set this if your device is struggling to play the output (dropped frames). - - - + + + + + Adjust encoder settings to trade off compression efficiency against encoding speed. + +This estabilishes your default encoder settings. Tunes, profiles, levels and advances option string will be applied to this. +You should generally set this option to the slowest you can bear since slower settings will result in better quality or smaller files. + + + + + + + + + - + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + - + - + + + + @@ -606,9 +682,11 @@ Set this if your device is struggling to play the output (dropped frames). - + - + + + @@ -616,7 +694,14 @@ Set this if your device is struggling to play the output (dropped frames). - + + + + + + + + -- cgit v1.2.3